Ubiquiti PBE-5AC-400-ISO | CPE | PowerBeam, 5GHz, 1x RJ45 1000M
British (UK) / GBP / Prices without VAT
Ubiquiti PBE-5AC-400-ISO | CPE | PowerBeam, 5GHz, 1x RJ45 1000Mb/s, 25dBi

Ubiquiti PBE-5AC-400-ISO | CPE | PowerBeam, 5GHz, 1x RJ45 1000Mb/s, 25dBi

CODE: PBE-5AC-400-ISO-EU / EAN: 810354023620
100,21 GBP without VAT
Number of LAN ports: 1x 10/100/1000BaseTX (RJ45)
Operating frequency: 5 GHz
Antenna gain: 21dBi - 30dBi


A breakthrough in performance

airMAX® ac products offer improved latency, noise immunity, scalability and significantly increased performance.

Innovative mechanical design

The integrated separator design improves RF isolation to filter out spatial interference, and the metal interior of the rear housing amplifies the radio frequency shielding.

ubiquiti pbe-5AC-400-ISO powerbeam

Excellent signal isolation

The integrated isolator design spatially filters out interference, so that PowerBeam ac ISO provides better signal quality. Both graphs near the field are displayed in watts and use a linear scale.

ubiquiti POWERBEAM 5AC 400 5GHZ 25DBI

Excellent data processing

Ubiquiti's airMAX® software with a custom chipset significantly improves TDMA delay and network scalability. The custom processor provides hardware acceleration capabilities for the airMAX schedule to support high data rate and dense modulation used in airMAX ac technology.

ubiquiti airmax ac

Advanced software

Ubiquiti's airMAX® technology has been proven in millions of devices worldwide, demonstrating exceptional performance in outdoor environments. The TDMA airMAX protocol enables unprecedented scalability, high throughput and low latency in unlicensed multipoint networks.

ubiquiti 5ac 400 5ghz 25dbi

A revolutionary operating system

airOS® v7 has increased usability and its basic functions are:

  • AirMAX ac protocol support
  • Long-range PtP
  • Selectable channel width
  • PtP: 10/20/30/40/50/60/80 MHz
  • PtMP: 10/20/30/40 MHz
  • Automatic channel selection
ubiquiti airmax airos

Radio spectrum analysis

airView enables identification of noise signatures and planning the network in such a way as to minimize interference. airView performs the following functions:

  • Constantly monitors interference levels
  • Collects data in real time spectral views
  • Helps optimize channel selection, network design
ubiquiti airview powerbeam

Breakthrough in data capacity

airMAX ac supports high data transmission speeds, which are as high as 450+ Mbps and require dense modulation: 256QAM has a significant increase over 64QAM, which is used in airMAX.

ubiquiti PBE-5AC-400-ISO airmax ac


Features / filters
LAN standard Gigabit Ethernet 10/100/1000 Mb/s
Number of LAN ports 1x 10/100/1000BaseTX (RJ45)
Operating frequency 5 GHz
Antenna gain 21dBi - 30dBi
CPU frequency 560 MHz
Device type Client device
RAM memory 64MB
Type of device power supply Passive PoE

Basic technical parameters
Dimensions 459 × 459 × 261 mm
Weight 3.22 kg
Power supply 24 V, 0.5A Gigabit PoE
Power supply Passive PoE (Pairs 4, 5+; 7, 8 Back)
Voltage range 20-26VDC
Maximum power consumption 8.5W
Frequency of operation 5150 - 5875 MHz
Strengthening 25 dBi
Network interface (1) 10/100/1000 Ethernet port
CPU specification Atheros MIPS 74Kc, 560 MHz
Memory RAM 64 MB DDR2, 16 MB Flash
LED indicators (1) Power
(1) LAN
(4) WLAN
LED signal strength Adjustable at software level to match RSSI levels
Supported bandwidths PtP mode 10/20/30/40/50/60/80 MHz
PtMP mode 10/20/30/40 MHz
Maximum VSWR 1.5:1
Built-in downward tilt mechanism ± 20°
Polarisation Two-line polarization
Case External UV-resistant plastic casing
Installation Columnal (parts included)
Wind resistance 559 N @ 200 km/h
Maximum wind resistance 200 km/h
ESD/EMP protection _± 24 kV, Contact ± 24 kV
Operating temperature -40 to 70° C
Humidity during operation 5 to 95%
Certificates FCC, IC, CE
RoHS compliance Yes
Corrosion resistance test 68-2-11 (ASTHMA B117),
Equivalent: MIL-STD-810 G Method 509.5
Vibration test IEC 68-2-6
Temperature test IEC 68-2-14
UV test IEC 68-2-5 in 40° C (104° F)
The equivalent: ETS 300 019-1-4
Cloud-busting test ETS 300 019-1-4
Equivalent: MIL-STD-810 G Method 506.5


Software Download
Quick start guide Download
Datasheet Download


How to connect the device to a PoE adapter?

1. Podłącz kabel Ethernet z portu Ethernet urządzenia do portu POE adaptera.
2. Podłącz kabel Ethernet z sieci LAN do portu LAN adaptera.
3. Podłącz przewód zasilający do portu zasilania. Podłącz drugi koniec przewodu zasilającego do gniazdka sieciowego.
ubiquiti pbe-5ac-400-iso powerbeam

What is the frequency of operation ?

Operating frequency 5 GHz

Types of power supply for the device ?

Device power type: Passive PoE

Choose a different country or region to shop in the language that suits you
Our site uses cookies (so-called "cookies"). You can find more about these files, as well as about how we process your personal data, in our privacy policy.
You are on page for country / region:
British (UK)
Please select a different country or region to shop in a language that suits you.