Cisco CBS220-24FP-4G | Switch | 24x RJ45 1000Mb/s PoE, 4x SFP, Desktop, Rack, 382W

CODE: CBS220-24FP-4G-EU

Cisco CBS220-24FP-4G | Switch | 24x RJ45 1000Mb/s PoE, 4x SFP, Desktop, Rack, 382W

CODE: CBS220-24FP-4G-EU
612,86 EUR without VAT (net)
Out of stock
Number of LAN ports: 24x [10/100/1000M (RJ45)] 4x [1G (SFP)]
Number of PoE ports: 24x [802.3af/at (1G)]
Built-in modem: None
Show more parameters
Recommended products
Subscribe to the NEWSLETTER and receive 5EUR* for shopping
Save
* Offer valid for orders from 45EUR |Regulation|

Promotions

New products

Discounts

ABOUT PRODUCT

Cisco Business 220 Series Smart Switches

TheCisco Business 220 Series is an affordable, intelligent switch that provides ease of use, security, and reliability for business-class networks. With an intuitive control panel, Power over Ethernet (PoE) options, and configurable features, these switches deliver a reliable business network within budget parameters. If you need a business-class network and cost is a top priority, the Cisco Business 220 Series is the ideal solution.

CISCO CBS220-24FP-4G 24-PORT 10/100/1000 POE SWITCH, 4X SFP, 382W

Cisco CBS220-24FP-4G Switch

The Cisco CBS220-24FP-4G is a professional Layer 2 switch with extensive management features and robust network security. This model has 24 Gigabit Ethernet ports and 4 Gigabit SFP uplink ports. With 56 Gbps throughput, it creates lightning fast connections to connected devices such as access points, computers, and IP phones. All Gigabit Ethernet ports on the Cisco CBS220-24FP-4G support full PoE (802.3at) power with a total power budget of at least 382 watts. This means that you can power devices directly over the network cable, as long as they also support PoE. This way, you do not need a separate outlet for each device. The Cisco CBS220-24FP-4G supports the energy-efficient Ethernet standard (IEEE 802.3az) to save power. Power consumption is adjusted according to cable length and port traffic. In addition, the port automatically enters sleep mode when it is idle.

CISCO CBS220-24FP-4G 24-PORT 10/100/1000 POE SWITCH, 4X SFP, 382W

Easy setup and management

With Cisco Business 220 Series Switches, you can not only build an efficient and reliable network to connect your workforce, but also create advanced solutions for delivering data, voice, and video services over a converged infrastructure. Get the best value for your money by increasing employee productivity.
Possible deployment scenarios include: Networking for small offices. The versatility and affordability of the Cisco Business 220 Series provides the ideal foundation for a business-class network for small businesses with limited IT support and budgets.

CISCO CBS220-24FP-4G 24-PORT 10/100/1000 POE SWITCH, 4X SFP, 382W

SPECIFICATION

Features / filters
LAN standard Gigabit Ethernet 10/100/1000 Mb/s
Number of LAN ports 24x [10/100/1000M (RJ45)] , 4x [1G (SFP)] ,
Number of PoE ports 24x [802.3af/at (1G)]
Built-in modem None
Management By web browser
Power (W) 382
Switching layer 2
Type of case Rack (1U), Desktop,

Basic general data
Manufacturer Cisco
Model CBS220-24FP-4G
Type Switch
Performance characteristics
Throughput in millions of packets per second (mpps) (64-byte packets) 41.66 mpps
Gigabit per second (Gbps) switching capacity 56
Layer 2 switching functions
MAC table Up to 8,192 MAC addresses (Media Access Control)
Spanning Tree Protocol (STP) Standard 802.1d spanning tree support, enabled by default.
Rapid convergence using 802.1w (Rapid Spanning Tree [RSTP])
Support for multiple spanning tree instances using 802.1s (MSTP)
16 instances are supported
Port Grouping Support for IEEE 802.3ad Link Aggregation Control Protocol (LACP)
Up to 8 groups
Up to 8 ports per group with 16 candidate ports for each (dynamic) 802.3ad link aggregation
Load balancing based on source and destination MAC address or source and destination MAC/IP address
VLAN Support for up to 256 virtual local area networks (VLANs) simultaneously
Port-based and 802.1Q tag-based VLANs
Management VLAN
Guest VLAN
Automatic voice VLAN Voice traffic is automatically assigned to its specific VLAN and treated with the appropriate QoS level.
QinQ VLAN VLANs transparently traverse the service provider's network while isolating traffic among clients
Generic VLAN Registration Protocol (GVRP) and Generic Attribute Registration Protocol (GARP) Protocols for automatically propagating and configuring VLANs in a bridged domain.
HOL (Head-of-Line) Blocking Prevention of HOL blockage
Jumbo frames Supported frame sizes up to 9,216.
Loopback detection Loopback detection provides loopback protection by sending loopback protocol packets from ports on which loopback protection is enabled. It operates independently of STP.
Automatic switching between media-dependent interfaces (MDIX) Automatically adjusts the transmit and receive pairs if an incorrect cable type (crossover or straight) is installed.
Security
ACLs Remove or restrict bandwidth based on source and destination MAC address, VLAN ID or IP address, protocol, port, Differentiated Services Code Point (DSCP)/IP priority, Transmission Control Protocol (TCP)/User Datagram Protocol (UDP) source and destination port, 802.1p priority, Ethernet type, Internet Control Message Protocol (ICMP) packets, Internet Group Management Protocol (IGMP) packets, TCP flag
Supports up to 512 rules
Port security Ability to block source MAC addresses on ports; limit the number of MAC addresses learned
IEEE 802.1X (authentication role) 802.1X: Remote Authentication Dial-in User Service (RADIUS); guest VLAN;
Single-host, multiple-host and multisession modes.
RADIUS, TACACS Supports RADIUS authentication and Terminal Access Control System (TACACS); the switch operates as a client
MAC Address Filtering Supported page
Storm control Broadcast, multicast and unknown unicast
Protection against DoS attacks Prevention of DOS attacks
STP Bridge Data Unit (BPDU) Guard Protocol This security mechanism protects the network from incorrect configurations. A port enabled for BPDU Guard is disabled if a BPDU message is received on that port.
Spinning Tree Loop Guard This feature provides additional protection against Layer 2 forwarding loops (STP loops).
Secure Shell (SSH) Protocol SSH is a secure replacement for the Telnet protocol. SCP also uses SSH. SSH v1 and v2 are supported. supported.
Secure Sockets Layer (SSL) SSL Support: Encrypts all HTTPS traffic, enabling highly secure access to the browser-based management GUI on the switch.
QoS
Priority levels 8 hardware queues per port
Scheduling Strict priority and Weighted Round-Robin (WRR) queues assigned based on DSCP and Class of Service (802.1p/CoS)
Class of service Port-based; 802.1p VLAN priority-based; IPv4/v6 IP precedence, Type of Service (ToS) and DSCP; Differentiated Services (DiffServ); ACL classification and relabeling, trusted QoS
Speed limitation Inbound policing; outbound shaping and rate control; per VLAN, per port and flow-based
Avoiding congestion A TCP congestion avoidance algorithm is required to reduce and prevent global TCP loss synchronization. Synchronization.
IPv6
IPv6 IPv6 host mode
IPv6 over Ethernet
Dual stack IPv6/IPv4
IPv6 Neighbor and Router Detection (ND)
Stateless IPv6 address auto-configuration
Maximum Transmission Unit (MTU) per Path Detection
Duplicate Address Detection (DAD)
ICMP version 6
IPv6 ACL Dropping or rate limiting IPv6 packets in hardware
IPv6 QoS Hardware-based prioritization of IPv6 packets
Multicast listener detection (MLD v1/2) Snooping Deliver IPv6 multicast packets only to required recipients
IPv6 applications Web/SSL, Telnet/SSH server, DHCP client, DHCP Autoconfig, Cisco Discovery Protocol (CDP), Link Layer Discovery Protocol (LLDP)
Management functions
Cisco Business Dashboard Direct management support with Cisco Business Dashboard and mobile app. Eliminates the need to configure separate hardware or virtual machine for on-premise Cisco Business Dashboard probes.
Cisco Business mobile app Mobile app for Cisco Business Switch and Wireless products. Helps you configure your local network within and provides easy management at your fingertips.
Cisco Network Plug and Play (PnP) agent The Cisco Network Plug and Play solution is a simple, secure, unified, and integrated offering that makes it easy to deploy new devices in branch offices and campuses or upgrade an existing network. The solution provides a unified approach to delivering Cisco routers, switches, and wireless devices in a zero-touch deployment.
Cisco PnP Connect support
Web user interface Built-in switch configuration utility for easy device configuration via browser (HTTP/HTTPS).
Support for configuration, dashboard, maintenance and system monitoring
Text-editable configuration files Configuration files can be edited with a text editor and downloaded to another switch, facilitating mass deployment.
Command line interface Scriptable CLI; full CLI is supported. User privilege levels 1 and 15 are supported for the CLI.
SNMP Simple Management Network Protocol (SNMP) versions 1, 2c and 3 with support for traps and SNMP version 3 User-based security model (USM)
Remote monitoring (RMON) The built-in RMON software agent supports 4 RMON groups (history, statistics, alarms and events) to improve traffic management, monitoring and analysis.
Dual stack IPv4 and IPv6 Coexistence of both protocol stacks facilitates migration
Reproduction of ports Traffic on a port or VLAN can be mirrored to another port for analysis using a network analyzer or RMON probe. Up to 8 source ports can be mirrored to one destination port. Four sessions are supported.
Firmware Update Upgrade over web browser (HTTP/HTTPS) and TFTP (Trivial File Transfer Protocol)
Dual images for a robust firmware update
DHCP (Option 12, 66, 67, 82, 129 and 150) DHCP options allow tighter control from a central point (DHCP server) for IP address, auto-configuration (with configuration file download), DHCP forwarding and hostname.
Time synchronization Simple Network Time Protocol (SNTP)
Login banner Configurable multiple banners for both website and CLI
Other management HTTP/HTTPS; TFTP update; DHCP client; Bootstrap Protocol (BOOTP); cable diagnostics; ping; traceroute; syslog
Power over Ethernet
802.3af PoE or 802.3at PoE provided by any of the RJ-45 network ports within the specified power budgets
PoE power budget 382 W
Number of PoE-capable ports 24
Hardware features
Buttons Reset button
Wiring type Category 5 Unshielded Twisted Pair (UTP) or better for 10BASE-T/100BASE-TX; Category 5 UTP
Ethernet or better for 1000BASE-T
LEDs System, Link/Act, Speed
Flash 64 MB
CPU memory 256 MB
Ports
Total number of system ports 28 x Gigabit Ethernet
RJ-45 ports 24 x Gigabit Ethernet
Uplink ports 4 x Gigabit Ethernet SFP
Packet buffer 4.1 Mb
Environmental features
Dimensions 440 x 257 x 44 mm
(17.3 x 10.1 x 1.7 in)
Weight 4.10 kg
(9.04 lb)
Operating temperature 0-50° C
Storage temperature -20° C to 70° C
Humidity during operation 10% to 90%, relative, non-condensing
Storage Humidity 10% to 90%, relative, non-condensing
System power consumption 110V=30.8W
220V=30.8W
Power consumption (with PoE) 110V=459W
220V=445W
Heat dissipation (BTU/hour) 1,566.17
Acoustic Noise and Mean Time Between Failure (MTBF)
Fan (quantity) 2
Acoustic noise 25°C: 43.2 dB
MTBF @ 25°C (hours) 588,411

SUPPORT

Files to download

Data sheet Download
Quick reference guide Download

FAQ

How many ports does the CBS220-24FP-4G switch support PoE?

The Cisco CBS220-24FP-4G switch supports 24 ports of PoE power .

612,86 EUR without VAT (net)
Out of stock
Print version
Session will expire in:
Seconds
You will be logged out after the session expires
Choose a different country or region to shop in the language that suits you
Our site uses cookies (so-called "cookies"). You can find more about these files, as well as about how we process your personal data, in our privacy policy.
You are on page for country / region:
English (EN)
Please select a different country or region to shop in a language that suits you.