EN
The device now has only fully independent Ethernet ports, each of which is directly connected to the processor, which allows you to break the previous common 1Gbit restriction from switching chips and use the full processing power potential of the processor on these ports. Combo-port - a single 1Gbit software interface that has two hardware interfaces - SFP and Gigabit Ethernet port, allowing you to use any available connection. It is also possible to switch between both physical interfaces in RouterOS. In case of disconnection, the combo-port provides hardware emergency switching function.
Support SFP 100Mbps is MikroTik's first device to support 100BASE-LXE/100BASE-SX/100BASE-BX fiber modules as well as standard SFP 1.25G modules. This device is equipped with a passive cooling chassis and a specially designed heat sink, making it completely silent. It is powered by an external 24V 2.5A AC/DC power supply and supports power redundancy. The device also includes LCD touch screen, microSD and SFP+port for 10G connections.
Features / filters | |
Number of LAN ports | 8x [10/100/1000M (RJ45)] , 1x SFP (1,25G), |
AC input voltage | 100 - 240 |
Additional connectors / interfaces | 1x USB, RS232, |
Built-in processor | Yes |
Cabling technology | 10/100/1000Base-T(X) |
CPU frequency | 1 GHz |
DC-in jack | Yes |
Depth | 190 |
Ethernet interface type | Gigabit Ethernet |
Ethernet LAN | Yes |
Ethernet LAN (RJ-45) ports | 7 |
Ethernet LAN data rates | 10,100,1000 |
Ethernet WAN | Yes |
Firewall | Yes |
Firmware upgradeable | Yes |
Harmonized System (HS) code | 85176990 |
Height | 47 |
Installed SFP modules quantity | 1 |
Installed SFP+ modules quantity | 1 |
Internal memory | 2000 |
Internal storage capacity | 0.128 |
Management | By web browser, CLI - Command Line Interface, |
Number of CPU cores | 9 |
Operating system installed | RouterOS |
Operating temperature (T-T) | -20 - 60 |
Power consumption (typical) | 33 |
Power over Ethernet (PoE) | Yes |
Power source type | AC, PoE |
Processor cores | 9 |
Processor frequency | 1000 |
Processor model | Tilera TLR4-00980CH-10CE-A3b |
Product colour | White |
Rack capacity | 1U |
Rack mounting | Yes |
RAM memory | 2GB |
Reset button | Yes |
RS-232 ports | 1 |
SIM card slot | Yes |
Smart Interface Card (SIC) slots quantity | 1 |
Temperature monitoring | Yes |
Throughput | 18 |
Type of case | Metal |
Type of device power supply | Passive PoE, Power supply, |
USB ports quantity | 1 |
Voltage monitoring | Yes |
Web-based management | Yes |
Width | 272 |
Basic technical parameters | |
Nominal processor frequency | 1 GHz |
Number of processor cores | 9 |
RAM | 2 GB |
10/100/1000 Ethernet ports | 7 |
Number of USB ports | 1 |
Socket | 1 |
Input PoE | Yes |
Supported input voltage | 14 V - 57 V |
Voltage monitor | Yes |
Processor temperature monitor | Yes |
PCB temperature monitor | Yes |
Dimensions | 272×190×47 mm |
Operating system | RouterOS |
Tested ambient temperature | -20C +60C |
Licence level | 6 |
Monitoring | Yes |
CPU | TLR4-00980CH-10CE-A3b |
Maximum power consumption | 33W |
Ports SFP+ | 1 |
USB power reset | Yes |
USB socket type | microUSB type AB |
Serial port | RS232 |
Type of memory | NAND |
Storage size | 128 MB |
User name is 'admin' and there is no password (press 'Enter'). To change password use '/password' command.
If you have not turned off the router, the filesystem has not been unmounted properly. During startup, RouterOS will perform a filesystem test. Depending on the size of your hard drive, this may take several minutes. Do not interrupt the file system test!
Yes! Access to the router is protected by username and password. Additional users can be added if necessary. Each user group can be assigned specific rights. You can restrict access to the router, which is protected by a user name and password. Additional users can be added to the router; specific permissions can be set for user groups. Remote access to the router can be restricted by the user, IP address. Firewall filtering is the easiest way to protect your router and network.