EN
OmniTIK 5 PoE ac has five Gigabit Ethernet ports and 802.11ac support. It has a more powerful 720 MHz processor (QCA9557), more RAM (128 MB), dual high power 802.11a/n/ac wireless chain (AC and 802.11a/n CPE backwards compatible), and a new weatherproof outer casing that protects the device from the elements.
OmniTIK 5 PoE ac version also supports passive or standard PoE 802.3at/af input/output. The Ethernet 2-5 ports can power other PoE-capable devices with the same voltage as the device. It can power devices operating in B-mode (4.5+)(7.8-) if the 48-57 input voltage is used. In addition, it has a high power radio - up to 31 dBm (1300 mW) and two built-in omnidirectional antennas with 7.5 dBi gain. The model has 5 Gigabit Ethernet ports and an additional USB port. It works only in 5 GHz band, it is not a dual band access point.
Features / filters | |
LAN standard | Gigabit Ethernet 10/100/1000 Mb/s |
Number of LAN ports | 5x 10/100/1000BaseTX (RJ45) |
Operating frequency | 5 GHz |
Wireless network standards | IEEE 802.11a, IEEE 802.11ac, IEEE 802.11n, |
5 GHz | Yes |
AC adapter included | Yes |
AC input voltage | 12 - 57 |
Antenna gain | Under 10dbi |
Antenna gain level (max) | 7.5 |
Built-in processor | Yes |
Cables included | AC |
CPU frequency | 720 MHz |
DC-in jack | Yes |
Depth | 58 |
Device type | Client device |
Ethernet LAN (RJ-45) ports | 5 |
Ethernet LAN data rates | 10,100,1000 |
Flash memory | 16 |
Harmonized System (HS) code | 85176990 |
Height | 416 |
Internal | No |
Internal memory | 128 |
Maximum data transfer rate | 54 |
Mounting kit | Yes |
Networking standards | IEEE 802.11ac,IEEE 802.3af,IEEE 802.3at |
Placement | Pole |
PoE adapter included | Yes |
Power consumption (max) | 18 |
Power over Ethernet (PoE) | Yes |
RAM memory | 128MB |
Type of device power supply | Passive PoE |
USB 2.0 ports quantity | 1 |
USB connector type | USB Type-A |
Width | 129 |
Product code | RBOmniTikPG-5HacD |
CPU | QCA9557 |
Architecture | MIPSBE |
Number of processor cores | 1 |
RAM | 128 MB |
Number of LAN ports | 5 Gigabit Ethernet 10/100/1000 Mbps ports Automatic MDI/MDIX crossover |
Type of built-in memory | Flash |
USB port | Yes, type A (1) |
LEDs | Yes (10) |
Radio system | QCA9892 2x2 MIMO, standard 802.11a/n/ac |
Number of radio tracks | 2 |
Frequency range | 5150 - 5875 MHz |
Antenna | Two omnidirectional antennas with 7.5 dBi gain |
Power supply | Passive PoE 12 - 57 V |
Maximum power consumption | 18 W |
PoE output | Yes, the Ether2 - Ether5 ports |
Maximum current per port | 1 A at a voltage below 30 V 0,5 A at a voltage above 30 V |
Dimensions | 416 x 129 x 58 mm |
Operating temperature | From -40 to 70 degrees C |
Operating system | RouterOS |
License | Level 4 |
Voltage monitor | Yes |
PCB temperature monitor | Yes |
PoE out | 802.3at/af |
SFP socket | No |
Power Jack | No |
Integrated antenna | Yes |
The most important feature that sets MikroTik's CPE and Bridge devices apart from the competition is their adaptation to the urban environment. In this respect, they have been optimized and consequently become more reliable. They are characterized by maximum resistance to interference, which is of great importance in today's increasingly crowded urban radio environment.
Please note that client devices equipped with indoor housings (e.g. indoor Access Points) cannot be mounted outside. In the case of Bridge Client devices with integrated antenna it is very important to install them properly. The antenna mountings (or masts) have to be stable, so they should be equipped with extraction brackets. Keep this in mind, as it affects the performance of the wireless network.
Since PoE allows the use of a single cable for power and data transmission, this solution saves money on purchasing and laying cables for network devices and VoiP phones.
PoE devices can be connected in one network with devices that do not work with it, but the latter cannot power PD devices or be powered by PSE devices. Devices that do not work with PoE must have a separate power supply.