The Ubiquiti ROCKETDISH RD-2G24 antenna is a high class device with a frequency of 2.4GHz and a distinctive energy gain of 24dBi. RocketDish RD-2G24 has been designed to work with devices using 802.11n standard. Ubiquiti antenna easily integrates with RocketM radio. The radio together with RD-2G24 antenna create a powerful PtP 2x2 MIMO bridging application. It is a flexible and convenient solution for network designers.
The airMAX antennas have been designed for a robust design for outdoor applications.
RocketDish and Rocket devices are designed to be easy to install and work with any other Rocket device. The parabolic antenna does not require any additional parts or tools. The mounting parts of RocketM devices correspond to the dedicated mountings used in airMax antennas.
| Features / filters | |
| Antenna frequency | 2.4 GHz |
| Energy gain | 21dBi - 30dBi |
| Antenna gain level (max) | 24 |
| Antenna type | Directional, Sector antenna, |
| Application | Outdoor |
| Certification | EN 302 326 DN2 |
| Compatible with brand | Ubiquiti |
| Cross polarization isolation | >35 dB |
| Depth | 650 |
| Frequency band | 2.3 - 2.7 |
| Front-to-back ratio | 28 dB |
| Height | 295 |
| Horizontal beamwidth | 6.6° |
| MIMO Type | 2x2 |
| Mounting | Wall |
| Polarization | Double linear, Dual polarization, |
| Product colour | White |
| Quantity per pack | 1 |
| Vertical beamwidth | 6.8° |
| Voltage Standing Wave Ratio (VSWR) | 1.6:1 |
| VSWR | 1.6:1 |
| Weight | 9.8 |
| Width | 650 |
| Basic technical parameters | |
| Frequency band | 2.3 - 2.7 GHz |
| Gain | 24 dBi |
| Horizontal beamwidth | 6.6° (3 dB) |
| Vertical beamwidth | 6.8° (3 dB) |
| Reverse radiation | 28 dB |
| Maximum VSWR | 1.6:1 |
| Dimensions | 650 × 650 × 295 mm |
| Weight | 9.8 kg |
| Wind survivability | 200 km/h |
| Wind load | 787 N @ 200 km/h |
| Polarisation | Horizontal and vertical (Dual-Linear) |
| Insulation between the polarization | 35 dB min |
| ETSI | EN 302 326 DN2 |
| Installation equipment | Universal pole bracket, mounting brackets for RocketM, waterproof coaxial cable included |
1. Each M4 Bolt includes a lock washer. Remove these and use them to secure the bolts when assembling.
2. The Dish Reflector and Antenna Feed are keyed so the Antenna Feed can only be installed in a single orientation. Attach the Antenna Feed to the Dish Reflector in the following steps:
a. Line up the alignment pin on the Dish Reflector with the hole on the Antenna Feed.
b. Insert the four M4 Bolts into the Antenna Feed and Dish Reflector.
c. Tighten the four M4 Bolts.
3. Attach the RocketM to the Dish Reflector.
a. Align the mounting tabs on the back of the RocketM with the Rocket Mounting Bracket located below the Antenna Feed.
b. Slide the RocketM down to lock it into place.
4. Attach the RF Cables to the connectors labeled Chain 0 and Chain 1 on the RocketM.
5. The Elevation Rod includes washers and nuts. Remove one washer, one spring lock washer, and one nut. Use them to secure the Elevation Rod when assembling.
6. Attach the Elevation Rod to the Main Mounting Bracket.
a. Insert the Elevation Rod into the Main Mounting Bracket.
b. Secure the Elevation Rod with the washer, spring lock washer, and nut.
7. Each M10x150 Carriage Bolt includes a washer, spring lock washer, and nut. Remove these and use them to secure the bolts when assembling in step 13.
8. Insert the four M10x150 Carriage Bolts into the Main Mounting Bracket.
9. Each M10x25 Carriage Bolt includes a washer, spring lock washer, and nut. Remove these and use them to secure the bolts when assembling.
10. Attach the RocketDish to the Main Mounting Bracket.
a. Insert one M10x25 Carriage Bolt into the RocketDish and Elevation Rod.
b. Insert two M10x25 Carriage Bolts into the RocketDishand lower section of the Main Mounting Bracket.
c. Secure each M10x25 Carriage Bolt with one washer, one spring lock washer, and one nut.
11. Each M10x100 Bolt includes a washer, spring lock washer, and nut. Remove these and use them to secure the bolts when assembling.
12. Attach the Stabilizer Brackets to the pole just beneath the area where the RocketDish will be attached.
a. Place one Stabilizer Bracket on each side of the pole.
b. Insert the two M10x100 Bolts into the Stabilizer Brackets
c. Secure each M10x100 Bolt with one washer, one spring lock washer, and one nut.
d.Tighten the nuts to approximately 50 N-m.
13. Attach the Main Mounting Bracket to the pole just above the Stabilizer Brackets.
a. Slide a Pole Clamp over each pair of M10x150 Carriage Bolts.
b. Secure each M10x150 Carriage Bolt with one washer, one spring lock washer, and one nut.
14. Visually align the azimuth and elevation.
a. To adjust the azimuth, rotate the RocketDish while it is supported by the Stabilizer Brackets.
b. To adjust the elevation angle, tighten or loosen the nuts on the Elevation Rod so that the RocketDish is set to the desired tilt.
c. Tighten all bolts and nuts to approximately 50 N-m or less to avoid deforming the pole
Antenna frequency: 2.4 GHz
Antenna type: Directional
