The Ubiquiti RocketDish RD-5G34 antenna is a high class device operating in the 5GHz frequency band and distinguishing itself with an energy gain of 34dBi. RocketDish RD-5G34 has been designed to work with devices using 802.11n standard. Ubiquiti antenna easily integrates with RocketM radio. Radio together with RD-5G34 antenna create a powerful bridging application PtP 2x2 MIMO. For network designers it is a flexible and convenient solution.
The airMAX antennas have been designed for a robust design for outdoor applications.
RocketDish and Rocket devices are designed to be easy to install and work with any other Rocket device. Installation of the Ubiquiti RocketDish 5GHz 34dBi dual parabolic antenna does not require any additional components or resources.
| Features / filters | |
| Antenna frequency | 5 GHz |
| Energy gain | >31 dBi |
| Antenna gain level (max) | 34 |
| Antenna type | Directional, Directional antenna, |
| Application | Outdoor |
| Compatible with brand | Ubiquiti |
| Cross polarization isolation | >35 dB |
| Depth | 1050 |
| Frequency band | 5.15 - 5.85 |
| Front-to-back ratio | 42 dB |
| Height | 421 |
| Horizontal beam width | 3 |
| Horizontal beamwidth | 3° |
| Mounting | Wall |
| Polarization | Double linear |
| Product colour | White |
| Purpose | Outdoor |
| Quantity per pack | 1 |
| Vertical beam width | 3 |
| Vertical beamwidth | 3° |
| VSWR | 1.4:1 |
| Weight | 13.5 |
| Width | 1050 |
| Basic technical parameters | |
| Frequency band | 5.1 - 5.8 GHz |
| Gain | 34 dBi |
| Horizontal radiation angle | 3° (3 dB) |
| Vertical radiation angle | 3° (3 dB) |
| F/B Ratio | 42 dB |
| Maximum VSWR | 1.4:1 |
| Dimensions | 1050 × 1050 × 421 mm |
| Weight | 13.5 kg |
| Wind resistance | 200 km/h |
| Wind load | 1,779 N @ 200 km/h |
| Polarisation | Horizontal and vertical (dual) |
| Insulation between the polarization | 35 dB min |
| ETSI | EN 302 326 DN2 |
| Installation equipment | Universal pole bracket, mounting brackets for RocketM, waterproof coaxial cable included |
1. Every M4 screw has a locking washer. Remove them and use to secure the screws during assembly.
2. The antenna dish and antenna feed are keyed, which means they can only be assembled in a certain orientation. Attach the device to the dish in the following steps:
a. Adjust the antenna feed to fit the hole on the dish.
b. Insert six M4 screws to the dish
c. Tighten six M4 screws.
3. Connect the RF cables to the Chain 0 and Chain 1 ports on the RocketM.
4. Attach the RocketM to the dish.
a. Adjust the mounting tabs on the back of RocketM to fit the mount
b. Slide the RocketM down to lock it in place.
5. Connect the rest of the cables to their ports on the antenna.
6. Attach the protective shroud.
a. Adjust the arrow on the top of the shroud to match the short arrow on the dish
b. Turn the shroud clockwise until it matches the marking
7. The elevation rod has washers and nuts, remove one washer, spring washer and nut. Use them to secure the rod during assembly.
8. Attach the elevation rod to the main mounting bracket.
a. Insert the rod to the main mounting bracket.
b. Secure the rod using washers
9. Every M12x180 carriage bolt has a washer, spring washer and a nut. Remove them and use to secure the bolt in step 15.
10. Insert four M12x180 screws to the main mount bracket.
11. Every M10x25 bolt has a washer and a spring blockade. Remove them and use them to secure the bolt during assembly.
12. Attach the RocketDish to the main mount bracket.
a. Insert M10x25 to the RocketDish and the elevation rod.
b. Insert two M10x25 bolts to the RocketDish and the lower part of the main mount bracket.
c. Secure each M10x25 bolt using washers.
13. Every M10x100 bolt has a washer and a spring blockade. Remove them and use them to secure the bolt during assembly.
14. Attach stabilizer brackets to the pole just below where the RocketDish will be.
a. Insert one stabilizer bracket on every side of the pole.
b. Insert two M10x100 bolts to the stabilizer brackets.
c. Secure every M10x100 bolt using one washer, spring and nut.
d. Tighten the nuts to about 50 N-m
15. Attach the main bracket to the pole just above the stabilizer brackets.
a. Slide the pole brackets onto every pair of M12x180 bolts.
b. Secure every M12x180 bolt using a washer, spring washer and a nut.
16. Set the azimuth and elevation visually.
a. To adjust the azimuth, turn the RocketDish when it is held up by stabilizer brackets.
b. To adjust the tilt tighten or loosen the nuts on the elevation rod so that the RocketDish is at the appropriate tilt angle.
c. Tighten every bolt and nut to about 50 N-m or less, to avoid deforming the pole.
