MikroTik RB4011iGS+5HacQ2HnD-IN | WiFi Router | Dual Band 1733Mb/s, 10x RJ45 1000Mb/s, 1x SFP+
CODE: RB4011IGS+5HACQ2HND-IN / EAN: 4752224002693
Contact
Account
Favorite
Cart
The RB4011iGS+5HacQ2HnD-IN routerboard is a wireless router that uses the incredibly powerful quad-core Cortex A15 from Amazon's Annapurna laboratory, just like the other RB1100AHx4 class carrier device. The router works in 2x2 MIMO technology for 2.4 GHz and 4x4 MIMO for 5 GHz. CPU supports hardware IPsec acceleration. It has 1 GB of RAM, so it can easily handle any task that has been configured in RouterOS. All this power is contained in a compact, black solid metal housing with a matte finish.
The presented routerboard is a two-band, four-chain device with supported data throughput up to 1733 Mbps operating in 5 GHz. It is compatible with older devices, it also has 2 GHz dual-chain interface. The wireless router is equipped with large external antennas with 360 degrees of coverage. Ten Ethernet ports guarantee 1 Gbps throughput, while the SFP+ port provides an optional 10 Gbps link through a SFP+ module (not included).
| Features / filters | |
| Antenna type | External |
| Antennas quantity | 4 |
| Built-in processor | Yes |
| DC-in jack | Yes |
| Depth | 120 |
| Ethernet LAN | Yes |
| Ethernet LAN data rates | 10,100,1000 |
| Ethernet LAN interface type | Gigabit Ethernet |
| Height | 30 |
| Output current | 0.6 |
| Output voltage | 57 |
| Power consumption (typical) | 26 |
| Power over Ethernet (PoE) | Yes |
| Power source type | DC |
| Processor cores | 4 |
| Processor frequency | 1400 |
| Processor model | Annapurna Labs Alpine AL21400 |
| Product colour | Black |
| Product type | Tabletop router |
| Top Wi-Fi standard | Wi-Fi 5 (802.11ac) |
| Wi-Fi band | Dual-band (2.4 GHz / 5 GHz) |
| Wi-Fi standards | 802.11a,Wi-Fi 5 (802.11ac),802.11ad,802.11g,Wi-Fi 4 (802.11n) |
| Width | 228 |
| WLAN data transfer rate (max) | 1733 |
| Product code | RB4011iGS + 5HacQ2HnD-IN |
| Architecture | ARM 32bit |
| CPU | AL21400 |
| Number of processor cores | 4 |
| CPU frequency | 1400 MHz |
| Dimensions | 228 x 120 x 30 mm |
| Operating system | RouterOS |
| Licence level | 5 |
| RAM | 1 GB MB |
| Ethernet ports | 10 Gigabit Ethernet ports 10/100/1000 Mbps |
| SFP+ slots | 1 |
| Serial Port | RJ45 |
| DC socket | Yes, 12 - 57 V DC |
| PoE input | Yes, port 1, 18 - 57 V DC (passive PoE) |
| PoE output | Yes, port 10, up to 57 V DC (passive PoE) |
| Maximum power consumption | 23 W (device only) 44 W using PoE |
| Built-in memory | 512 MB |
| Switch chip | RTL8367SB |
| Voltage monitoring | Yes |
| PCB temperature monitoring | Yes |
| Permissible operating temperature | From -40° to 45°C |
| Set composition | Device, 24 V power supply, 2.5 A, IEC cable |
| Wi-Fi frequency | Dual-band (2.4 GHz/5 GHz) |
| Radio standards | 802.11b/g/n 802.11ac |
| Polarisation | 2.4 GHz - 2x2 MIMO (dual chain), 5 GHz - 4x4 MIMO (quad chain) |
| Data carrier | NAND |
| Ethernet LAN interface type | Gigabit Ethernet |
SFP modules allow to connect the main board of a switch, router or other device to a fiber optic cable (single-mode, multi-mode) or to a copper cable (twisted pair).
MikroTik RouterOS is an operating system based on Linux, which has been specially designed to build advanced access points and routers with bandwidth management capabilities.
The main, but not the only difference between these turnouts is speed.
Ideally, 2.4 GHz WiFi will support up to 450 or 600 Mbps, while 5 GHz can reach up to 1300 Mbps.
But beware! The maximum speed depends on the Wi-Fi standard used by the router, i.e. 802.11b, 802.11h, 802.11n or 802.11ac.
